Chimney flashing repair in Ewing, New Jersey done right the first time
Chimney flashing repair in Ewing, New Jersey is the fix that keeps rain from running down your chimney and into your ceilings. If you have seen water stains on the ceiling near the chimney, rust streaks on the flashing, or loose metal at the roof line, you are looking at failed flashing. We reseal, rebuild, or replace it so your roof and chimney stay dry through every storm. Call (844) 803-5147.
Service overview
Chimney flashing repair in Ewing, New Jersey explained
Chimney flashing repair in Ewing, New Jersey is the work of rebuilding the metal seal where your chimney passes through the roof. Flashing is the layered metal system - step flashing, counter flashing, and base flashing - that sheds water around the chimney opening. When it rusts, lifts, or pulls away from the masonry, rain runs straight down the chimney chase. We remove the failed metal, cut a clean reglet into the brick, set new copper or aluminum flashing, and seal it with the right caulk and counter flashing so water never gets a second chance. Most Ewing homes we see were built between the 1920s and the 1980s, and their original flashing has long since given out. Ice dams along the roofline, summer storms, and decades of freeze-thaw cycles work the metal loose until a small gap becomes a ceiling stain. If you have been searching for chimney flashing repair near me in Ewing, the fix is usually a half-day job once we get on the roof. We also handle chimney flashing replacement Ewing homeowners need when the old metal is too far gone to reseal.
! Common warning signs
Water stains on the ceiling near the chimney
The stain spreads, insulation gets soaked, and the roof deck starts to rot. By the time the ceiling sags, you are looking at a tear-off around the chimney instead of a flashing repair.
Rusted or lifted flashing at the roof line
Rust means the metal has thinned and the seal is already broken. Lifted flashing lets wind-driven rain straight into the chimney chase, and the leak gets worse with every storm.
Spalling brick and crumbling mortar at the chimney base
Water behind the flashing freezes, expands, and pops the brick faces off. Left alone, the chimney loses structural strength and can eventually need a full rebuild from the roofline up.
Scope of work
What our flashing repair includes
A flashing repair is not just a bead of caulk. Here is what we actually do on your roof, and what we will tell you about if we find it while we are up there.
-
01
Full roof-level inspection
We inspect the step flashing, counter flashing, base flashing, chimney crown, and cap before quoting. A camera inspection system checks the flue interior for water damage. You get photos of everything we find, whether or not it needs work today.
-
02
Removal of failed flashing
Old step flashing and counter flashing come off without damaging the surrounding shingles. We cut a fresh reglet groove into the brick with an angle grinder so the new counter flashing seats into the masonry instead of sitting on top of it.
-
03
New copper or aluminum flashing
We install new flashing in overlapping layers so water always sheds down and out. Copper is the long-term choice; aluminum is the budget option. Both are sealed with polyurethane caulk rated for masonry and exterior exposure.
-
04
Water test before we leave
We run a hose over the repair for 10 minutes and watch the attic side. If it stays dry, we clean the gutters, sweep the roof line, and walk you through the work. If it does not, we keep going until it does - that is on us, not you.
What proper flashing repair protects
Failed flashing does not fix itself. Every storm pushes more water into your attic, your insulation, and your chimney masonry. Here is what a correct repair actually buys you.
Get a quoteTools and methods we use
Camera inspection system
Lets us see inside the flue and photograph the flashing from the roof without guessing. It is how we confirm whether a leak is flashing, crown, or cap before quoting the repair.
Angle grinder with masonry blade
Cuts a clean reglet groove into the brick so new counter flashing seats into the masonry. This is the difference between a repair that lasts decades and one that leaks again next season.
Masonry trowel and mortar hawk
Used to repoint mortar joints and reset brick disturbed during the flashing repair. We match the existing mortar color so the repair blends into the chimney.
Waterproofing sprayer
Applies breathable water repellent like ChimneySaver or SaverSystems to the brick after flashing work. It keeps the masonry from soaking up rain and extends the life of the repair.
Local execution
Ewing sits between the Delaware River and the coastal plain, which means wet winters, ice dams, and plenty of freeze-thaw cycling on the roofline. That cycle is what kills flashing. Water gets behind the metal, freezes overnight, and pries it loose a little more each time. Most of the chimneys we repair here are on homes built between the 1920s and the 1970s, with brick that has already been through decades of this. We also see a lot of 1980s and 1990s construction near Mountain View and Rosedale where the original aluminum flashing has finally given out. If you have been putting off chimney flashing repair in Ewing, the fall is the right time - get it sealed before the first hard freeze. We work to NFPA 211 and New Jersey chimney sweep license standards on every job, and we pull permits when Ewing Township requires them for masonry work.
How flashing repair runs in Ewing
- • Ewingville
- • West Trenton
- • Mountain View
- • Scudders Falls
Recent work
Same-day and emergency flashing repair in Ewing
When water is coming in, we answer
A flashing leak during a storm is not a wait-until-Monday problem. Our phone line stays open 24/7 at (844) 803-5147, and you reach a real person who can talk you through shutting down the fireplace and protecting the ceiling until we arrive. For active leaks, we aim to have a technician on site within a few hours anywhere in Ewing, West Trenton, or the surrounding Mercer County area. Our trucks carry copper and aluminum flashing stock, polyurethane sealant, tarps, and a camera inspection system, so most emergency calls turn into a permanent repair the same day or the next clear day. For non-emergency chimney flashing repair Ewing homeowners can schedule a morning or afternoon window that fits their week. We confirm the arrival window by text and call ahead when we are on the way.
How our flashing repair process works
Roof and attic inspection
We start on the roof and work down. A camera inspection system checks the chimney interior while we photograph the flashing from every angle. We also look inside the attic for staining, wet insulation, and daylight around the chimney chase. This takes 30 to 45 minutes and tells us whether you need a reseal or a full replacement.
Written findings and price
Before any metal comes off, we show you the photos and explain what failed. You get a flat price for the repair - no hourly surprises. If the crown, cap, or masonry also need work, we tell you now and let you decide what to do first. Most flashing-only jobs land between $350 and $850.
Removing the old flashing
We pull the old step flashing and counter flashing without damaging the surrounding shingles. An angle grinder cuts a fresh reglet groove into the brick so the new counter flashing seats properly. This is the step most quick-fix crews skip, and it is why their repairs leak again within a year.
What flashing repair costs in Ewing
Flashing repair pricing in Ewing depends on roof pitch, chimney height, and how much of the assembly needs rebuilding. A simple reseal with new caulk and minor counter flashing work starts around $350. A full chimney flashing replacement Ewing job with new copper step flashing and a reglet cut runs up to $850. If the crown, cap, or masonry also need work, we quote that separately so you can decide what to do now and what can wait. You get a flat price before we start - no hourly billing, no surprises.
Roof pitch and access
A steep roof or a chimney set back from the ridge takes longer to work on safely. We use roof anchors and harnesses, which adds time. A walkable roof with easy access keeps the price at the low end of the range.
Flashing material
Aluminum flashing is the budget option and works fine for most homes. Copper costs more up front but lasts two to three times as long. On a chimney you plan to keep for decades, copper is usually the better value.
Extent of masonry damage
If water has been getting in for years, the brick and mortar around the flashing may need repointing before the new metal goes on. That adds time and materials. Catching the leak early keeps the job in the flashing-only price range.
Frequently asked questions
How much does chimney flashing repair cost in Ewing?
Most flashing repairs in Ewing run $350 to $850 in 2026. A simple reseal with new caulk and minor counter flashing work sits at the low end. Full chimney flashing replacement Ewing jobs with new copper step flashing and a reglet cut land at the top of that range. Roof pitch, chimney height, and whether the crown or cap also need work are the main variables. You get a flat price before we start.
What is chimney flashing fixing in Ewing New Jersey?
Chimney flashing fixing in Ewing New Jersey is the repair of the metal seal where your chimney meets the roof. That seal has three parts - base flashing, step flashing, and counter flashing - and water leaks when any one of them fails. Fixing it means removing the failed metal, cutting a fresh groove into the brick, installing new flashing, and sealing it against the masonry so rain sheds away from the chimney instead of running down it.
How do I know if my chimney flashing needs repair in Ewing?
The clearest signs are water stains on the ceiling or attic rafters near the chimney, rust streaks on the metal at the roof line, and flashing that lifts when you press it. You may also see granules from the shingles collecting around the chimney base. If you spot any of these, call (844) 803-5147. A 30-minute inspection with our camera system confirms it, and most repairs are done the same week.
Who does chimney flashing repair near me in Ewing?
Link Tough does. We have served Ewing and the surrounding neighborhoods since 2022, working to CSIA Certified Chimney Sweep standards and NFPA 211. We handle everything from a small reseal to full chimney flashing replacement, plus crown repair, tuckpointing, and chimney waterproofing when the masonry needs it. Call (844) 803-5147 and we will get eyes on your roof this week.
Related services
Chimney Repair Near Me
If your flashing leak has already damaged brick or mortar, our general chimney repair service handles the masonry side. We fix both in one visit so you are not paying two trip charges. Ewing homeowners get a single flat price for the whole job.
Chimney Masonry Repair
Water behind failed flashing freezes and pops brick faces. Our masonry repair rebuilds spalled brick and deteriorated mortar joints before we seal new flashing over them. Doing the masonry first is what makes a flashing repair last more than one winter in Ewing.
Get chimney flashing repair in Ewing, New Jersey this week
Every storm that hits a failed flashing pushes more water into your attic and your masonry. We inspect, quote, and repair with a workmanship warranty on the seal. Call (844) 803-5147 or request a quote online and we will get eyes on your roof.